How to Replace the Replacement Key Battery For the Saab 9-3

saab 9-3 key replacement owners must follow a set of special steps to install a second ignition key. This requires the use of a handheld computer, known as Tech-2 which is to be used by the dealer. Then the transponder is replaced and a key must be purchased.

Make sure to rotate your keys in order to prevent one from wearing out quicker than another. This will help keep your keys in good condition.

Replacement Case

Contrary to the classic saab 93 key fob keys of old keys, the modern key fobs have electronics inside that make it difficult to duplicate. That has made car theft considerably more difficult than it was a few years ago. It has also made it more expensive to replace keys lost.

Saab 9-3 owners must have two working keys. If one is lost, it is expensive to add another to the car since it requires replacing the CIM module and reprogramming the locking cylinders. Dealers usually charge between $100 and $200 for this.

There are some ways around these expensive. Some parts retailers can look up the code on an old key (usually the same one that opens the doors and turns on the ignition) and cut a new key blade out of metal for only a fraction of the dealer's cost. The key must be the exact same as the original for it to function in your vehicle.

You can also replace the case yourself by following these steps. You'll require an flathead screwdriver and patience. With the screwdriver, you can pry apart the plastic and remove the emergency key. Once the case is open, remove the electronics and put them back into the new case. Make sure you insert the correct key and badge inside the case.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost component that can be replaced quickly and easily. This DIY video from YouTube Cyclone Cyd will show you how to replace the battery for the remote key fob in just four steps. This tutorial is suitable for any modern saab key fob, although the process might differ slightly.

The first step is to locate the button that will release the backup key in the fob. This button is typically located on the back of your fob just below the Saab Logo. Use a flathead to insert the screwdriver in the small hole in this button. This should be enough to open the fob's case to allow you to replace the battery.

After the new battery CR1632 is in place then you can reassemble your remote key fob. You can then program it to your car. The entire process shouldn't take more than an hour. It's a simple process that does not require any special equipment.

If you lose your key, the process is a bit more involved however it can be completed. The dealer has to find the VIN number of the car and then order a replacement key blade and TWICE module, both with the proper unique code. The dealer will then have to program the key using MDI which is a new software tool.

Replacement Key Fob

The key fob is equipped with an internal battery that is used to lock and unlock your vehicle. Batteries have a limited lifespan and eventually will die. This is a common problem that happens with all cars, and the good news is that you can replace the batteries in most fobs, without replacing the entire case. Amazon sells replacement fobs with all the electronics in place. It is easy to pop the case open and replace the batteries. You will need to remove the emergency key before you can replace the batteries. To do this, place an small screwdriver with a flat head into the slot in the middle. Move the screwdriver around the case, and it will split open, making it simple to take it out.

If you're planning to replace your keys, have a spare in your possession. This can save you a lot of money. If you do have a spare, you can ask the dealer cut an additional key and program it to the car, which is cheaper than replacing the whole key fob.

It is possible to add another key to your vehicle even if you don't have one, but it will require some research and effort. A second key can cost several hundred dollars and it also requires the programming of the car's computer. Professionals can do this, but it's an expensive option.

Replacement Ignition

The modern SAAB 9-3 is an advanced alarm system built on a keycode. If you lose your only key, it could be costly to get another one, as the car has to have a specific computer installed and be programmed to accept a new key. Dealers can charge hundreds of dollars to program the new key if they are unable to complete the task.

Dealers will charge you a high price to replace your car's computer (also called the CIM or saab 9-3 key twice) when you lose your sole working key. Instead we can reprogramme the EEPROM on your existing car computer to allow it to be programmed for a replacement key, and save you over 50% of what you'd spend at a dealer.

If you've been a long-time owner of an 03-11 saab key programming near me 9-3, then you likely know that the ignition key isn't very robust. If your ignition key isn't functioning properly, it is time to think about replacing it. They can become sticky and the buttons can fall off. Luckily, replacing the ignition key isn't as complicated as it seems and can be done in a short time with the appropriate tools.