Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain and are durable and long-lasting. They don't get rotten or rusty like aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and may even be fatal. It is essential to take the time to make sure that you are doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and typically fit into old frames very easily. If you have double-paned windows that are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this situation, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you're planning to attempt to remove the window panes by yourself it is important to wear the proper safety gear, including thick gloves and protective eyewear. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric, not onto the floor, where they could be trampled under.

Once the glass is removed from the window, it's best to cover the gap with packaging tape or duct tape to block water and drafts from getting into the home until a professional can come out and repair the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the gap is large, you might be interested in the security door with an integrated window as this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. Over time, they can be affected by a variety of issues that include sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. It's important to take action immediately if you realize that your uPVC windows are sliding.

Repositioning the hinges can help fix a window that is sagging. To do this, you'll need to open the window so that you can access the frame. After that, using an screwdriver, remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have repositioned your hinges. If you're satisfied with the fit, tighten the screws to ensure that they remain in the right place.

If you are unable to move the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity over time, which causes them to loosen. If this happens, it's important to replace the seal as soon as possible so that your uPVC windows remain watertight and secure from draughts.

UPVC handles can also become loose. Often this is due to screws that have come loose over time. However, it could also happen because the handle mechanism has worn out. It's relatively simple to fix a loose uPVC hand. The first step is to close the window and perform an experiment to ensure that it fits. The corner joints of the sash should be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it is important that you take action. The leaks of water from windows do not only lead to the degrading of the structure of your home but also hinder your efforts to control the temperature within your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be done by anyone who is a DIYer with the skills. Depending on how serious the issue is, the old caulking may need to be removed. It is important to remember that when it is about uPVC window repairs (like it), do avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and reduce your energy efficiency.

Make sure that the drainage holes are free of debris in them and ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you may have to replace the window.

Other indicators of water leakage include rotted sills and the appearance of black spots of mold on the wall near the window. This mold thrives in damp environments and can quickly spread across the home.

If the leakage is occurring between the double glazed window repairs-glazed glass, it is more likely the problem is related to the seal, not the frame. Again this can easily be fixed by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or it opens with the breeze. Any competent DIYer can replace the hinges in a matter of minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that are hinged and, like all mechanical parts, they can wear down over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier to do with someone else to help hold the frame up.

Make sure that the uPVC hinges are open and closed in the correct direction. This can be done by looking for the arrows on each hinge, this indicates the direction in which the window should open.

Faulty window hinges could be caused by improperly opening the window in a particular way or by poor installation at the factory. This issue can be fixed by sending us a photograph via our website and we will be happy to give you suggestions.

Regularly lubricating the hinges is essential. This can be accomplished by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It also decreases the chance of windows sticking and help prevent corrosion. This must be done at a minimum once a year. WD40 and other solvent-based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of different factors. First, the hinges because of wear and tear, can become misaligned, this will cause gaps to develop between the sash and the frame. If they are beyond repair, it could be necessary to have them realigned. The interlock, which is on the hinge side of the window and can be misaligned. Again, it may be possible to give them a clean but in some cases it might be necessary to have them replaced.

These seals can wear down or become damaged over time, allowing air escape. Installing high-quality weatherstripping can help stop draughts. Replace the windows made of upvc with low-emissivity lenses. This will help regulate indoor temperatures and lessen the risk of draughts.

The last way to reduce the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be placed over your window sill. These will help to keep cold air out and keep your home warm and cozy!

With a little maintenance and repair windows made of upvc will provide excellent security and insulation for your home. It is important to remember that all windows will eventually wear out and it may be more cost-effective to replace them than to repair them. If you are experiencing issues with your upvc window, it's best to consult an expert as soon as possible.