UPVC Replacement Door Handles

Over time, the handles on your doors will wear down and will require replacement. When replacing them, it is essential that the new handles match the dimensions of the handle that was previously used.

The top screw position the lever, and the keyhole sizes are the three measurements you have to determine. Check the size guide for assistance with this.

Inline Lever/Lever

A lever or lever door handle is a contemporary handle that can be used on replacement or new doors. This kind door handle is available in a variety of styles and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are constructed of durable materials and are suitable for multi-point lock doors that require a strong design. The handles are inline and use the same spindle and screws to fix them. They can be easily installed on a new or existing uPVC/Composite door.

The handle can be positioned and angled to suit all users. The handle has been tested for endurance up to 200,000 cycles. This helps ensure that the quality of finish and performance over time. The lever that is sprung can be cut to fit more locks. This is especially useful in doors with smaller door frames in which the cylinder is further back. A shorter lever can be used for doors with a latch that can be activated with the thumb inside.

Lever Pad

A Lever Pad door handle made of upvc operates differently than lever handles that are found on the majority of doors. These handles can use a single spindle (inline) or independently from each side using two offset or inline spindles (pad). They are typically utilized on UPVC doors with double glazing window handles glazing. They come in a range of finishes and variations.

The handles have been tested to the minimum of 200 000 cycles and are available in a variety of finishes including White and Silver, as well as Chrome & Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the aluminium window handle a high degree of durability and performance for its intended use.

All UPVC levers for handles come with a spindle, screws and can be mounted on the uPVC door. The backplate fixation centers of 211mm permit a larger handle, which is usually beneficial when replacing a damaged or old multi-point door lock mechanism. The levers for these handles have a spring, which solves the issue of door double glazed handles that move out of the horizontal position when not being used.

It is important to match up the PZ dimensions for both the multipoint lock and the uPVC doors when choosing a replacement UPVC spindle and handle. This measurement is also known as the 'handle centre' or 'cylinder centres which is a crucial aspect of matching up the appropriate handles.

Once you have the correct PZ size, you'll have to ensure that the handle lever pads and push pads are a appropriate shape to accommodate the American with Disabilities Act (ADA) compatible handles you need for your doors. These are typically of a round or square design with an internal lever as well as an external push pad.

The majority of the UPVC Lever Pads that we offer are spring-loaded. This means they will return to a horizontal state when they are not in use, rather than hanging and possibly sticking in the frame. This prevents draughts from entering the home. You will also find that the majority of upvc handle window handle lever pad style handles are hand-operated, allowing you to install them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. They operate by using a key that unlock a cylinder case that is then revealed with pins that can be aligned with those in the lock body and allow them to rotate a revolving cam, thus opening the door. Euro cylinders can be equipped with up to six pins, with both internal and external doors generally needing different levels of security.

The choice of the correct cylinder is vitally important; this is dependent on how your doors and handle are used. For example, external doors should be fitted with a higher security cylinder, while internal doors can be secured using an ordinary cylinder. Additionally, certain cylinders are available with extra features that increase security, for instance anti-drill and anti-bump characteristics.

A euro cylinder should be properly measured to ensure it is the correct size for your door. The cylinder should be measured from the hole in the center of the fixing screw to the end of the cylinder including the thumb turn if you have one. If you cannot measure with the lock in position, you can remove it. It is essential to not have a extension of the cylinder beyond the handle or escutcheon. This could make it vulnerable to snapping lock attacks.

The majority of modern cylinders have been designed with anti-drill and bump resistance features that are built into their design. These are designed to reduce attack chances by forcing the cylinders to rotate in a different direction. This will help to deflect the attack and ensure your doors are secure.

There are cylinders that have been constructed to resist snapping. This is an increasingly common type of attack on cylinders where the break line in the lock is targeted by a tool that is specially designed to snap off the front of the cylinder and allow the door to be opened. This is a lot faster and less difficult than gaining access through multipoint locks and leaves no evidence of a break-in, which can hinder the insurance claim.

Spring Cassette

This spring cassette is found inside the base plate of your door handle. It offers a spring-loaded solution to return your multipoint lock handles back to their normal position after using. The handles had no spring and would drop when the locking window handle mechanism was disengaged. This component is the best way to address this issue. It also stops your door from getting stuck in the open or closed position as they aren't easy to close manually.

These spring cassettes were created to be used with sprung multipoint lock. They will not fit handles that aren't sprung and you'll need to cut a hole in your backplate in order for them to fit. (Please look at the image for a more detailed diagram). These cassettes can be used as a replacement to broken or missing cassettes in the backplate of uPVC door handles. They have a square cut-out that can accommodate an 8mm spindle, and are available in a variety of.

These spring cassettes provide an excellent value solution to the problem of door handles that have become sagging. They are easy to fit and will extend the life span of your uPVC doors. For more information on our selection of uPVC accessories and spares, you can get in touch with our team. We are always ready to offer professional advice and assistance you.