Replacement UPVC Door Handles

Find the perfect handle for your door, whether you are replacing your existing handles or adding additional security. Upvc handles are simple to fit and comply with the required 92mm centres of multipoint locks.

The most important measurements to take into consideration are backplate fixing centres as well as key hole dimensions and levers. Compare these measurements with your existing measurements prior to making a purchase.

Lever/Pad

Lever pad handles for doors consist of a lever handle on one side and a paddle-shaped handle on the other. They are intended for use with key wind locks. However they can be affixed to multipoint split spindle door locks.

Our range of upvc handles lever pads are available in a wide range of finishes. These will be shown in the drop down list after you have selected the right handle for your doors. Not all styles of handles are available in every finish though and you should always check the technical drawings and sizes sections for the particular product you're looking for to ensure that you get the correct size and fitting.

When selecting the new set of upvc lever pad victorian door handle handles it is important to ensure that they match the PZ (distance between the handle spindle and the center of the cylinder hole) of your existing multipoint locks, as they need to be in the same line to allow doors to remain locked, either from the inside or the outside. Our handles are designed to fit a wide range of standard cylinders, but it is always worth double glazed window handle-checking before ordering.

If you want to upgrade to dual spindle levers you'll need to take out the handles you have already installed and disassemble the lock case. This will require an extra split inline cylinder. You can purchase these separately. We have included a diagram of the technical aspects in the images of each product.

It is recommended to loosen the screws that are holding your door handle, and then check the mechanism. If the screws are too tight then you might need to loosen them further. Then you can remove the spindle from the door handle and replace upvc door handle it with your new Upvc handle. Before putting the handle in the frame, it is a good idea to ensure that it is in the correct place. You can do this by placing your finger into the gap between the frame of the door and the handle to make sure that it is level.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock with a Euro cylinder. They are located on many double upvc doors as well as some wooden and aluminium doors. They feature a lever inside and an outside paddle and are generally available in two varieties. Sprung - These have a spring cassette inside the backplate, which helps bring the handle lever to an upright position. Non-sprung: These do not have a mechanism to spring the handle lever to a horizontal angle.

To fix a sagging lever door handle it is necessary to find the hole for access to the detent or pin, which is usually an elongated or rectangular shaped hole or protruding pin that is located on the opposite side of the base plate. Once you have located it, loosen the set screw with a screwdriver and remove it to allow the lever, allowing it to return to the horizontal position.

When the handle is in a horizontal position, you can re-install the screws and tighten them so that the handle stays fixed to the base plate. Consider applying a threadlocking product to the screw threads in order to improve grip and prevent the threads from becoming loose over time.

There are many reasons why door handles of levers slide. The most common reason is that the fixings aren't tight, causing the lever bearing to get tangled against the door. It could also be that the levers are not being operated in a straight line and this is causing compression of the latch mechanism and preventing it from fully springing back into operation.

A common cause of a spring lever not operating correctly is the spring not being in the proper position on the backplate. To determine whether the handle is back to horizontal, simply move it.

It is important to fix any loose door handles as soon as possible. This could cause excessive wear on the screws and the handle might be able to fall off the base plate. It is recommended to tighten all loose screws on a regular basis, as this will help to prevent them from loosening.

Lever/Snib

The handles for doors made of upvc are also known as handle sets with a 'Snib' and feature a snib button on the top of the lever that you can push down to lock your door in the event that you don't use a dummy lock. They are usually fitted with a Fullex 68PZ (that's 68mm between the spindle's center and lever or the lock centre) door lock. We also have a range of other door handles with 68PZ from manufacturers such as Ferco and Fab & Fix.

The replacement of your door handle is a cheap method to upgrade your home, whether you're replacing existing handles for internal bifold doors or fitting new ones to doors you've built in your house. There are a variety of styles of door handles made from upvc available, including traditional lever on backplate, curved or straight short latch and knob handles that resemble dummy knobs for multi point locks, which are perfect for French doors.

Lever on backplate handles are typically rectangular in shape but you can also find circular or oval shaped versions, which are known as rose door handles. These handles for doors are identified by a lever or knob that is attached to the backplate. The backplate can be removed to allow for hidden fixing.

There are a wide range of coloured and chrome finishes available for these handles that complement your door and other hardware, such as hinges, knobs, bolts and so on. Some handles for patio doors come with grub screws that aid in the secure attachment of the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to control bathroom locks and incorporate a thumbturn turn and release mechanism, ideal for bathroom doors.

Mortise

If your uPVC front door handle is stuck in the open position, the reason is most likely to be related to the tubular latch. This could be due to a number of things, but the most common is the lack of lubrication on the latch plate. It is possible to fix this problem by opening the door, spraying lubricant onto the lock and handle. It could also be that the latch plate is detached from the backplate. This can be a bit more of a problem and requires a professional to fix it.

A multipoint door handle is an ideal solution to the problem of a door handle that is stuck. These handles are attached to the faceplate and operated with a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles come in various sizes to fit different types of uPVC door, and come in various attractive finishes that complement the hardware that is currently in use. The handles can be bought online or through an authorized locksmith in your area. They are simple to install, with clear instructions.

You'll have to know your PZ size of your cylinder in order to select the right replacement handle set. This is the measurement in millimetres between the inner edge of the door frame and the centre of the handle hole. You'll also need the type of lock for your door, regardless of whether it's a mortise lock or a hook lock. The most effective way to locate the correct handles once you know the measurements is to use the filter for brands on the website. This will narrow down your options, and you will then choose the right size from there.

A typical handle set comes with the handle unit and a pair of different length screws drilling guides, as well as installation instructions. The smarter versions, such as the Igloohome Smart Mortise 2+ comes with the complete mortice lock, which has an integrated keypad. These are more sophisticated models and are ideal for professionals who install them or competent DIYers. Certain handle sets come with a range of other accessories, such as weather strips that can be used to enhance the look of the door.