How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. This key usually resembles the remote control and can be exchanged with a new one from a Kia dealer or a locksmith.

Key fobs can fail to function due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some suggestions to help you get your Kia sportage replacement key working for good.

How do you replace the remote key fob kia sorento or smartkey

Whether your kia picanto replacement key cost (you can try willysforsale.com) comes with an intelligent key, remote key, push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually need replacing. This is especially relevant if your vehicle displays a message that indicates the smart or remote keys aren't powered.

Luckily, this is an easy process. To replace the battery in the keyfob take out your mechanical key from the slot at the back of the fob. Then, pull the cover off. A small screw will be found inside the key fob that holds the battery in place. Using a small screwdriver, remove the screw and pull out the battery that was in place. Insert the new battery and then close the opening on the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or when you need to run errands around Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of metal) don't require programming. If your key needs to be programmed again, you will need to be aware of the key code number printed on the tag of the key code and keep the number in a secure place.

How do you replace a battery?

If the kia new key key fob doesn't respond to pressing the lock/unlock button, it's a sign that the battery is depleted. A battery that is not functioning properly could cause other issues like the check engine light turning on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires just a few tools.

Make sure you turn off your vehicle and shut all doors prior to beginning. Find the small metal or plastic piece near the bottom of the key fob. Press it until the key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and orient the new one in a way that the "+" positive side is facing you, while the "-" negative side is facing the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. You can then test the Kia's Key fob again to make sure it's working as intended.

How can you replace the smart key

You could have an ordinary keyfob or Smart Key, based on the model of Kia Sportage. The smart key features an embedded mechanical key blade however, the standard key fob does not. Both key fobs are equipped with a battery that will eventually require replacement. This is an easy process that takes only two minutes.

Make sure to shut off your 2013 kia sportage key fob and stand on a flat well-lit and well-lit area before you begin. Be aware that the fob can contain tiny parts that could fall should you not be careful.

The first step is to find the small release button that is located on the lower backside of your fob. This will be either an oval or circular slot. Once you press this, the mechanical key blade will be released and you can then open the key fob.

Once you have the key fob open it is easy to remove the old battery, and replace it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished, your key fob will allow you to lock and unlock your vehicle, even if it isn't running.

How do I replace a mechanical key

The 2007 kia sedona key fob programming key fob is a great convenience that allows us to lock and unlock our vehicle with the touch of one button. Like all devices like a key fob, the 2011 kia sorento key fob replacement might have issues. There are methods to troubleshoot these issues and ensure that our key fobs are in good condition in the long run.

A low or dead battery is one of the most frequently encountered issues. This could cause the fob to stop working entirely or to work intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't fix the problem, try using a standard flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. If the key fob isn't functioning, contact an authorized locksmith or dealer to help resolve the issue. To avoid lockouts in the future, ensure you have an emergency key that will work on all trunk and door cylinders.