Replacement UPVC Door Handles

You can find the ideal handle for your door, whether you are replacing your handles or adding security. These upvc handles are easy to fit and comply with the required 92mm centres for multipoint locks.

The backplate's fixing centre as well as the keyhole/lever dimensions are the most important measurements. Compare these measurements with your existing marks carefully before making a purchase.

Lever/Pad

Lever pad handles for doors consist of the lever handle on one side and a paddle shaped handle on the other. These are designed to be used with key wind locks, although they can also be used to multipoint split spindle door locks (though you'll need an additional dual spindle lock case).

Our selection of upvc handle lever pads are available in a wide range of finishes. They will be shown in the drop down list after you have selected the perfect handle for your door. Not all styles of handles are available in every finish and you should always check the technical drawings and sizes sections for the specific product that you want to make sure that you get the right size and fit.

It is important that when choosing a new set upvc lever pad handles, they match the PZ (distance from the handle spindle to the center of the hole of the cylinder) of your multipoint door locks. This is because the handles are required to be aligned for the doors to stay locked, regardless of whether you are looking from the inside or from the outside. The handles we offer are designed to work with a variety of conventional cylinder locks, however it is advisable to double-check before ordering.

You'll need to remove your handles that you have already installed and then dismantle the lock case if you are upgrading to dual spindle levers for your handle since this will require an additional split cylinder inline. You can purchase these separately. We have included a technical diagram in the images of each product.

It is a good thing to loosen the screws that are holding your existing sliding patio door handle replacement handle and then inspect the mechanism. You may need to loosen the screws even more in the event that they are not tight, and then you can remove the old handle and spindle and install your new upvc door handle. Before you screw the handle into position, it is recommended to check that it is in the proper place. You can do this by putting your finger in the space between the door frame and the door handle to ensure that it is level.

Lever/Lever

Lever door handles are a multi point lock using an Euro cylinder and can be found on a majority of double doors made of upvc, aluminum doors and some wooden doors. They have a lever inside and a paddle on the outside and are typically available in two types. Sprung - they come with a spring cassette within the backplate that helps move the handle lever to the horizontal position. Non-sprung - these do not include a spring mechanism and will require manual pulled to raise the handle lever to the horizontal position.

To repair a door handle lever that is sagging, you'll need to find the hole or pin that is the detent access point. This is usually an insignificant hole or protruding ring, or rectangle, that is located on the base of the handle plate. Once you have located the hole for accessing the detent or pin, you can remove it with the help of a screwdriver.

Once the handle has been placed horizontally, you can install the screws. Tighten them to ensure that the handle stays attached to the base plate. You should also consider applying a threadlocking adhesive solution to the threads of the screw to increase the grip and prevent them from loosing over time.

There are a variety of reasons why lever patio door handle handles drop. The most common reason is that the fixings are over tightened and are putting strain on the bearings of the lever, causing it to bind against the door face. It is also possible that the levers have not been adjusted at the right angle, which causes compression of the latch mechanism and prevents it from fully springing into motion.

Another reason is that the sprung lever is not functioning properly and this is usually due to the spring not being in the correct position within the backplate. To determine whether the handle is back to its horizontal position, simply turn it.

It is essential to fix any door handles that are loose as soon as possible. This can cause excessive wear on the screws, and the handle could be able to fall off the base plate. You should also tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

These upvc door handles are also referred to as handle sets with a 'Snib' and feature a snib button at the top of the lever that can be pressed down to lock your door in the event that you don't have the dummy lock. They usually come with a Fullex 68PZ (that's 68mm between the spindle's center and lever or the lock centre) door lock. We also have a selection of composite door handles handles 68PZ from manufacturers such as Ferco and Fab & Fix.

You can make your home more modern by changing the handles on your doors, whether you are replacing your existing handles or installing new ones on doors that you've constructed. There are a variety of styles of upvc door handle available that include traditional levers on backplate, straight or curving short latches, and knob handles with dummy handles for multi point locks that are perfect for French doors.

Rose door handles are oval or circular versions of backplate lever handles. These door handles are characterized by a lever or a knob that is attached to a backplate. The backplate is removable for concealed fixing.

There is a variety of chrome and coloured finishes available for these handles to match your door and other hardware, like bolts, knobs and hinges. Some handles are supplied with grub screws to help firmly attach the lever or knob to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and feature a thumbturn turn as well as a release mechanism, perfect to use on doors for bathrooms.

Mortise

The tubular latch is most likely to be the cause if your uPVC door handle is stuck open. There are a few things that can cause this, the most common being the simple lack of lubrication on the latch plate. This can be corrected easily by opening the door and spraying lubricant over the lock and handle. It could also be that the latch is loose from the backplate. This is a more difficult issue that requires an expert.

A multipoint handle is the ideal solution to stuck door handles. These handles mount through the faceplate of the door and are operated by the thumb turn knob or key that triggers a cam that locks the deadbolt. The handles are available in a range of different sizes to fit various kinds of uPVC doors. They are also available with a variety of attractive finishes that match the hardware you already have. These handles can be purchased online or from a local locksmith. They are easy to install and come with clear instructions.

You will have to know your cylinder's PZ size in order to select the right replacement handle set. This is the measurement in millimetres that lies between the outer edge of the frame of the door and the centre of the handle hole. You will also need to know if your door has hook locks or a mortise style lock. The easiest way to find the correct handle after you have the measurements is to use the filter for brands on the website. This will narrow down the options, and you will then select the correct size from there.

A typical handle set includes a handle unit, two screws of different lengths, drill guides and instructions for installation. Smarter versions, like the Igloohome Smart Mortise 2+ include a mortice lock complete with a keypad. These are more complex models that are best for professional installers or highly skilled DIYers. Some handle sets have a range of other accessories, like weather strips, that can be used to improve the appearance of the door.