Replacing uPVC Window Handles

It is simple to swap the handles on upvc windows. It is essential to make sure that the new handle fits inside the spindle cutouts in the window mechanism.

If you follow the steps below the handle of any cockspur will fit in most windows. The step height of the handle is key.

What to Look for

Many of the windows in the UK are fitted with uPVC handles, and over time they will begin to show signs of wear and wear and tear. The window handle may become shaky or difficult to operate when this happens. Anyone who is comfortable working with basic hand tools can accomplish this fairly simple task.

The first step is to ensure that the handle is securely fixed to the frame of the window in the open position. The next step is to locate the pins or screws that hold the handle. They are typically located on the inside of the handle. They can be removed with the screwdriver and pliers.

Once the handle has become loose and sagging, it can be removed from its hinges by gently pulling it off. It is then time to find a new handle of the same style and size. This can be accomplished in a DIY store or online. The process should take about five minutes and requires a screwdriver.

One important factor to consider when replacing a uPVC window handle is its step height. This is the distance between the handle's base and where it is located in the window handles for upvc frame. It is generally a standard measurement, and it is important to determine the step height of your current handle before purchasing the new one.

There are various sizes depending on the type of handle. Inline handles can be found for uPVC window with centers of 31mm for lugs, while cockspur handles come with centers of lugs of 43 millimetres. Tilt and turn handles are often used on windows made of uPVC, and they feature a specific design that allows windows to be slid up to allow for ventilation, and then turned to open the window completely.

The most frequent breakage in uPVC handles is that they crack internally instead of breaking away from the base section. This makes it difficult to open. It is essential to ensure that any replacement handle is fitted with the same spindle as the original one.

Remove the old handle

A poorly installed or damaged window handles could cause your double-glazed windows to open or close improperly and could even cause them to become stuck. There are a variety of reasons, such as general wear and tear, or corrosion of the handle made of metal. In these situations it is crucial to find replacement window handles made of upvc immediately to avoid further damage and loss of functionality.

One of the first steps that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Start by removing the screw covered when the handle in closed position. This will reveal a screw that once removed, you are able to begin to remove the handle itself. You can make the job easier by using an electric screwdriver.

It is also worth noting that the screws on the handle may be hidden behind caps made of plastic, so it is recommended to use the Stanley knife to the screw covers and take them off. After removing the old handle, you will have to examine the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is important because you'll need to determine the length of the spindle on the previous handle to ensure it is the same size as the window mechanism and the handle spindle that has been cut out.

The various types of upvc window handles are: Espag handles, which are equipped with a central screw and can be turned left or right; Cranked handles, that have two screws and are used on tilt and turn windows made of upvc and Spade handles with an arm with a flat surface and can be placed on either side of the window. When you have a suitable replacement, it is just a matter of screwing the handle into place and making sure that the spindle is placed into the lock mechanism. After that the handle should be secured to the window frame and the replacement upvc window handles should be secure.

Measure the Spindle

If you have to replace a upvc handle that has fallen, it's likely the spindle holding it in place is damaged or is loose. In some instances, you can tighten the spindle with pins or screws. In other cases it will need to be replaced entirely. There are many kinds of window handles made from upvc. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is installed and replaced in a different manner.

It is essential to measure the handle before buying an alternative. This will help ensure that the new handle is the right size and will fit correctly into the window. Luckily, all handles conform to industry standard sizing so it's fairly easy to find the right size.

To measure the handle's size you must turn the window to the open position. You should be able to determine the dimensions of the pin or screw that holds the handle. Use a ruler or tape measure to determine the length the spindle is. Once you know the length of your spindle it is possible to purchase a replacement of exactly the same length.

The step height of a upvc window handle is another factor to take into consideration when purchasing an alternative. The step height is measured from the base to the point at which the handle is placed on the frame. Typically, this is about 21mm for uPVC windows and 9mm for aluminum. Dropping something into the gap will let you see how far the handle extends before it reaches an obstruction.

Cockspur handles come with different backsets depending on what type of window you put them in. Inline espag handles have the standard height of 43mm from centre to centre (2 fixing points). Cockspur bi-fold doors handles however they have different backsets depending on the design of the window they're in. This is because they have a spur which extends from the handle and is locked onto a cockspur wedge hitting plate.

Install the New Handle

After you have chosen the new handle, ensure that it is aligned with the screw holes on the victorian door handle. Then, secure it with the screws provided. Install the latch lever the same way as the handle that you are replacing if you are also replacing the door handle. Finally, reattach the door trim to hide the mounting screws and close off your project.

Tips: To take the head of the metal from the wedge made of wood make sure the handle is held so that its wider end is resting on the floor. Then use an hammer to tap the thin end of the handle. Be careful not to scratch the handle or the spindle.